Search the Community
Showing results for tags '360mm Rad'.
Found 1 result
Greetings from the Dirty South PC Mods shop once again Mad Modding Monkeys This time I am going to be working on a Tribute build to Superman in Classic Colors. First off I would like to thank my Sponsors without their generosity my builds would not be anywhere near as awesome. http://www.icemodz.com/ https://www.facebook.com/Icesleeve https://www.facebook.com/tekbydesign http://www.lepatek.com/eng/ http://www.enermax.com/ Be sure and swing by their respective sites and FB pages to check out all the Killer Gear they have to make your RIG look Beast!!!! Here is a look at the Hardware that is going to be going into our build. CPU - Intel i5 3470 3.2ghz Quad-core /w Bitspower ICE Blue CPU Block Mobo - Biostar TZ77XE4(Custom Painted Blue Heatsinks, and Di-Noc) Ram - G.Skill Ripjaws 2133mhz DDR3 4 x 4Gb /w Bitspower Universal Ram Block kit Blue/Blue SSD - SANDISK 120Gb SATA III SSD PSU - LEPA MaxBron 700Watt 80+ Bronze certified RAD - XSPC 360mm Slim High Performance, Black Ice 360mm X-Flow Rad, XSPC 120mm Pump - XSPC D5 Vario /w Bitspower Mod kit(Blue) & PPC's Custom Pump Top Fittings - Primochill Ghost Compression 1/2" x 3/4" as well as a few Monsoon 3/4" 90-Deg rotary fittings Res - Bitspower 40mm tube Res Tubing - Primochill 1/2" x 3/4" tubing GPU - EVGA GTX 660Ti 2Gb & PNY GTX 660Ti (SLI) Fans - Enermax T.B. Vegas Trio 9 x 120mm, 1 x 180/200mm T.B. Apollish Blue and 1 x 140mm T.B. Apollish Blue(PSU Fan swap) So lets get this Build started. First off we did a live unboxing http://www.twitch.tv/dirtysouthpcmods/b/481331321 Then we Drilled out the Rivets for the I/O Plate & Cut a hole in the bottom of the Case to mount our XSPC 360mm Rad http://www.twitch.tv/dirtysouthpcmods/b/481499486 Here is a look at what it looks like. Perfect Fit!!!!!!!!! Then we painted the Chassis RED We then Painted the Chassis Red The Rad and I/O Plate Yellow Well thats it so far. Need to get some more paint. Be back later. Be sure to check out our weekly Live mod show every Wed 10am-2pm http://www.twitch.tv/dirtysouthpcmods Where was I ahh yes. Marking up the Side panels, and the Top panel for windows. Got them cut out and hung up for paint. Now I'm not going to lie this was a bit late after a long day. So my cuts weren't all that strait. Time to bust out the Grinder with a Flapper Wheel so these will have to re-painted. Currently I am at odds with keeping the Mobo tray and painting it. Or replacing the whole thing with 1/8 clear acrylic.However 1/8" acrylic tends to bow under weight. (That's why I usually use it for Windows.) Just hoping once I get the board on the Acrylic it will stiffen it up. Guess there is only one way to find out huh. Ok where was I ahh yes. Well decided to Paint the Mobo tray. Painted the Front Panel and Xigmatek GPU Coolers Handel and 5.25" bay covers Painted the Mesh Red...Looking good We were going to cut the top and put a window but with the release of a new Product by Enermax we have decided to leave it intact. Paint is done..Just waiting for the last bits to dry. Alright now that the Paint is done. It's time to see about squeezing all this hardware in here. Got the XSPC EX360mm Rad on the bottom topped off with Enermax T.B.Vegas Trio 120mm Fans. The Black Ice 360mm X-Flow Rad is mounted on the front with more Enermax T.B Vegas 120mm Fans. The Primochill CTR 240mm Res. All fitted with Monsoon Right Angle Rotary(3/4"), and Primochill Ghost Compression Fittings(1/2" x 3/4"). Got the Biostar TZ77XE4 Mobo w/ Custom Painted Heatsinks and Di-Noc Mounted to the Mobo Tray. The Bitzpower Blue ICE CPU Block and Ram Block /w Custom Di-Noc Trim. Kitted out with Monsoon Right Angle Rotary 3/4" and Primochill Ghost Compression Fittings 1/2" x 3/4" Mocking up the two GTX 260's(Thanks Angel Cruz for the sweet deal on the second card) With Xigmatek GPU Coolers(Before they were painted Blue) Whoaaaa thats a REALLY Tight fit. There is about 2mm to spare so the fans work fine. Alright now to address the stock screws. The solution Tek By Design "Proline" Button Head Fasteners(Polished) Thank you for your generous contribution to our build. Some of what will be posted next was covered in this weeks live show. http://www.twitch.tv/dirtysouthpcmods/c/3414063 Alright time to get started Modding our PSU, but first lets take a closer look at the inside. As you can see this PSU is Oozing with Quality Components Ok so first up is a Fan Swap on way to custom sleeving and paint. Stock Black Fan has got to know. Going to replace it with an Enermax T.B.Apollish 140mm in Blue Its already looking good. Just wait till I turn it on. Bazinga Now I gotta take it apart and Prep it for Paint. Well while I wait for the weather to clear up I'm going to get started on the sleeving process. Thank you Mundi from ICEMODZ for all your support. A look at all the awesome stuff from ICEMODZ. Thank you Mundi Ok so lets get started. First up the easy one Molex Next up Sata Cable. Now the Real work starts the 8 and 24-pin connectors Ok guys thats it so far Still waiting on the weather to clear up so I can paint the PSU. Right so the weather is still crappy so I'm still working on sleeving. And I'm out of Red Sleeving have to wait for more to come in. Alright While I'm waiting for the rest of my sleeving to come in Lets get busy with the rest of the PSU and a GPU upgrade instead of using 2 x GTX 260 I will be using 1 x GTX 660 Ti Tearing it apart Getting ready for its Wrapping And our 660 Ti is going to get the same treatment. Ok had a change of heart on the front panel. We ended up taking a couple pieces of clear acrylic and covered the back side with Red Vinyl. We then took some Blue Vinyl and cut out the sponsor logos with the vinyl cutter and put that on the front side of the Acrylic panel. Then we attached it to the front of the panel with 3M double sided tape. We then put one of our ICEMODZ.com Red LED's behind it and you get this effect. We did the same thing with the 3.5" hot swap bay. but with Yellow and there you have it. and of course after I have already painted the Mobo plate we got a wild hair and decided to go ahead and make a new one out of Plexi. We also decided to cut the Top panel and put a clear window on it. with a 200mm hole for our 180/200mm Enermax T.B.Apollish Fan (Blue) Look'n good Now to see about dealing with what can only be described as a Skittles Bag after it has been blown to pieces. Alright thats all I have at this time. Need to order a new Res as the Primochill CTR I already have sitting is wayyy too large. And I haven't Decided what I want to do with the GPU's yetI didn't like the Blue vinyl wrap so I ripped it off.