Search the Community
Showing results for tags 'recycled'.
Found 2 results
Hi guys my last mod case. motherboard ram cpu psu case are recycled! any questions comment are welcomed :-) ENJOY!! 45° w RECYCLED MOTHERBOARD CPU • Supports FM2+ Socket for AMD® A-series/ Athlon™ Series Processor Chipset • AMD A68H Main Memory • 2 x DDR3 memory slots supporting up to 32GB • Supports DDR3 2133(OC)/ 1866/ 1600/ 1333 MHz • Dual channel memory architecture • Supports non-ECC, un-buffered memory • Supports AMD Memory Profile (AMP) • Supports Extreme Memory Profile (XMP) Slots • 1 PCI Express x16 slot • 1 PCI Express x1 slot • 1 PCI slot, Support 3.3V/ 5V PCI bus Interface VGA • 1 x VGA port, supporting a maximum resolution of 1920x1200@ 60Hz, 24bpp • 1x DVI-D port, supporting a maximum resolution of 2560x1600@60Hz, 24bpp/ 1920x1200@60Hz, 24bpp On-Board SATA • 4 x SATA 6Gb/s ports - Supports RAID 0, RAID1 and RAID 10 USB • 2 x USB 3.0 ports on the back panel • 6 x USB 2.0 ports (2 ports on the back panel, 4 ports available through the internal USB connectors) Audio • Realtek® ALC887 Codec • Flexible 8-channel audio with jack sensing • Compliant with Azalia 1.0 Spec LAN • Realtek® RTL8111G Gigabit LAN Back Panel I/O Ports - 1 PS/2 mouse port - 1 PS/2 keyboard port - 1 VGA port - 1 DVI port - 2 USB 2.0 ports - 2 USB 3.0 ports - 1 LAN(RJ45)port - 3 x audiojacks Internal I/O Connectors - 1 x 24-pin ATX main power connector - 1 x 4-pin ATX 12V power connector - 4 x SATA 6Gb/s connectors - 2 x USB 2.0 connectors (supports additional 4 USB 2.0 ports) - 1 x 4-pin CPU fan connector - 1 x4-pin system fan connector - 1 x Front panel audio connector - 2 x system panel connector - 1 x Chassis intrusion connector - 1 x TPM module connector - 1 x Serial port connector - 1 x Clear CMOS jumper Dimension • Micro-ATX 22.6 cm x 17.3 cm Mounting • 6 mounting holes Motherboard is an msi military A68HM-p33 V2, https://it.msi.com/Motherboard/A68HM-P33-V2/Specification recycled from another PC it's have an integated gpu of 2GB!!!
hello guys this is an old pc case, my spot is to recycle as much as possible, I really enjoyed myself and I have experienced strange things that I did not know before, this is my first experience but I hope to continue, thanks to everyone for visiting .. I mentioned a project in my previous post nuclear server after several thoughts and evaluations, it's time, I opt for a different case I need something that is square and aggressive but above all RECYCLED, I pull out of my garage an old PC ATX mid tower, is anonymous and malconico, but no rust and inteno is in good condition, I have no intention of opening windows in the bulkhead right then I will just decorate the outside. First I remove all panels, 2 side panels, plastiva front and top panel and start sanding with 200 sandpaper, I do not care to do a job of finishing because this house is old and damaged deliberately.Together with the sandpaper I munisco a spray bottle to wet the surface of the bulkhead, and actually a lot better and does not raise dust. I dry everything. I'm going to open a vent in the upper bulkhead that will contain a grid decorated with written pc, can also insert 2 optional fans. I munisco scotch and imitation dremel, the preparatory phase is very delicate and it is worth losing a bit of time. I pause for a moment and prepare the logo to the computer that will be painted on the bulkheads. Mold on adhesive paper laser printing is fine but any inkjet printer also. Cutout with my knife precision. Before painting the bulkheads wipe with a lint-free cloth, this will allow the removal of the powder as an alternative advice NITRO thinner. After the 3 bulkheads painted in matt black, I place the strips of paper for the yellow stripes, I calculate that the yellow stripe puperiore will be divided into 2 in a laratia and the other in the top piece. Prefer carve out a piece of cardboard with the angle of 34/35 degrees 45 degrees is too. I position the logos. And go with spray!! I make it dry and proceed at the opening .... The yellow color was too liquid and has gone slightly under the masking tape, but this is not a problem, what I want is to create a very ruined houses, after removing all the masking tape, I munisco steel scourer , one for washing the dishes, and I begin to spoil what I just painted. It takes patience, but the result will strepoitoso and ruined at the right point, rubbing with steel wool all the smudges disappear, rubbing hard emerges a bit of white (original paint) and is perfect looks even more worn out .... I'm going to put 2 handles on the upper bulkhead, this will give a more evil. I'm going to be modding the dvd player that the floppy, then I remove all plastics, the clean up with steel wool removing the lettering, the clean up finally with a degreaser. And I paint with matte black. Since I have not removed totally the white color of the houses and readers, rubbing with steel wool, you see at the bottom originally as in effect giving a damaged bulkhead, perfect. Next phase grids matte black, the mask of the writing I used the same principle but in negative bulkhead, then painted yellow. And now .... prepare a hole for an optional fan and then place the grid decorated on the front panel. Cutting with false dremel. I set the pan with silicone, but it would be better to think of the perfect hot glue, silicone pette us too long to dry. This is the final result. Thank you for visiting my post and having accepted my bad English.